Menu
The Deck Foot Anchor for floating structures (non-ledger attached) gives you strength and security with a ground anchored connection with less labor, time and cost. Quickly and easily install ground anchored footings for freestanding decks, pergolas, sheds, ramps and more—in minutes!
The 3-¼" blade and 5" blade have tested in clay for maximum compression loads of 1,391# and 5,500# respectively.
If unsure about your soil conditions, we highly recommend testing your soil before purchasing Deck Foot Anchor products. Click here to see our test kit.
The Deck Foot Anchor installs with a handheld ½" impact wrench. Use our hand auger tool if you prefer a manual installation.
Turn a week-long job into a weekend project.
Save money on labor, materials and time.
No sledge or jackhammers or heavy machinery.
Install in the morning and build in the afternoon.
Some soil is not well suited for augers. The soil may be full of rocks, roots or other obstructions, or frozen. So you have to do some due diligence first to know if your soil is suited for this kind of solution.
If you're unsure about your soil conditions, we recommend using our Deck Foot Anchor - Test Kit for accurate results. This kit will help you assess soil composition and confirm compatibility with our augers before you buy, giving you confidence in your foundation choice.
If continuous torque is applied after hitting an obstruction, the auger may be damaged and become difficult to remove.
Additional Information
You can build your deck with joists as low as 2"-3" above grade if you wish. Simply hang the joists from the perimeter joist. If you want to extend the deck beyond the footing, extend the side perimeter joists 6"-10" and fill with blocking joists along the length.
With proper bracing in both directions from 6x6 posts to beams, you can make a six-foot high freestanding deck as solid as a rock. It's possible to go even higher but it is not intended to support decks at a second-floor elevation.
FRAMING AND BRACING TECHNIQUES
The Rule of Thumb is 6'-0" apart for each footing. This corresponds to a design load of 50 psf and tributary areas over each footing of 36 sqft.
So the total load imposed on the soil below each footing would be a maximum of 1800 psf as the footing is just slightly larger than 1 sqft.
If you have a large deck where three or more beams are going to be used, consider adding one additional footing along the interior beam. This is because the tributary loads of any structure are always greatest in the middle.
Designed for direct ground contact, the convex load plate ensures stability on compacted gravel or soil. Pairs perfectly with our Shorty or Tall Boy style Post Saddles.
Installs directly into the ground—no need for a hard surface.
Ideal for use on gravel, soil, or other compacted bases.
Provides a secure, anchored footing for your structure.
Our flat load plate allows simpler installations over pavers or stone. Pairs perfectly with our Shorty or Tall Boy style Post Saddles, or Pergola Brackets.
Remove enough pavers to allow the helical blade to clear.
Load plate rests on a hard surface.
Also useful over asphalt.
WHAT IF MY POSTS AREN'T 6x6 OR 4x4
For projects with posts that aren't using traditional 4x4 or 6x6 posts—or if you just prefer a more versatile mounting solution—our Pergola Post Brackets are the perfect choice.
They accommodate a wide range of post types, including wood, metal, hollow, and closed-bottom posts.
When using a solid wood post or a closed bottom metal post, an access hole for the drive head of the auger must be bored into the post (1-3/4" to 2" dia.).
A common bi-metal hole saw can be used to cut a hole in the flat bottom of metal post. This hole allows the drive head of the auger to reside inside the post.
This installation guide will walk you through securing the flat load plate over pavers using our Pergola Post Brackets, providing a strong and versatile foundation for your structure.
The flat plate rests on a hard surface while the helical anchor drives into the ground for added stability
If you prefer a more traditional approach, the brackets can be swapped out for our Shorty or Tall Boy Post Saddles, allowing you to customize your installation to fit your needs.
HOW DOES FROST AFFECT THE ANCHOR?
The Deck Foot Anchor™ is designed to remain securely in place, unlike traditional fence posts that can gradually lift out of the ground over time. It stays anchored while moving with the natural expansion and contraction of the soil during freeze-thaw cycles, ensuring long-term stability.
The Deck Foot Anchor - Floating™ is not promoted as a frost footing and falls under Section R403.1.4.1. Exception 3 (IRC) and Section 9.12.2.2.(7) (NBC). Therefore it is recommended for use with freestanding decks.
If you want a true frost footing that also accommodates ledger attached structures check out the Deck Foot Anchor - Ledger or the Ledger - Load Max
Here are the data from the compression tests of the auger in the best and worst type of soil.
Pull out resistance (tension) from undisturbed soil varies by soil type and auger length. If you are building a project where known uplift data is required please see our Tension Test data for sandy or clay soils based on auger length.
This is data taken from field testing by Intertek in a location in Colorado and is part of an extensive residential code compliance review program this is expected to be completed in 2022.
Optimal Times for Installing the Deck Foot Anchor
To ensure the best results and avoid potential damage, it's important to install the Deck Foot Anchor when the ground is fully thawed and free of frost. Attempting to drive the auger into frozen or partially frozen soil can cause excessive stress on the anchor, potentially leading to bending or breakage.
We recommend scheduling your installation during late spring, summer, or early fall — typically once overnight temperatures consistently stay above freezing and any frost has fully melted from the ground.
If you're unsure whether the frost line has completely thawed, it's best to test the soil with a metal rod or soil probe before installation. Soft, unfrozen soil will allow the Deck Foot Anchor to perform as designed, giving you a secure and lasting foundation.
While tightening the bolt to the plate, the auger was coming up out of the ground. I couldn't securely tighten the bolt. And because of that the post bracket wasn't secure enough to put a post in it
I had to call because of a few questions that I had regarding the product, talked to a gal named Sara? or Sarah?, either way, very helpful person and got everything taken care of for me. I am nominating her for employee of the month.
These anchors are fairly lightweight, durable and easy to install. They will be perfect for two sheds I'm building.
The deck anchors work fantastic. I’ve been using them for a few years ..110% satisfied. Great product and support!!!
I had to call because of a few questions that I had regarding the product, talked to a gal named Sara? or Sarah?, either way, very helpful person and got everything taken care of for me. I am nominating her for employee of the month.
With The right tools this entire system is fantastic. Saves time and energy for a perfect result.
We purchased 2 of the Deck Foot Anchors for a storage shed project that had a covered lean too attached to it for some animal cover. They worked great, were easy to install, and the building inspector was very impressed with them and we passed our inspection easily.
We used 6 of these to anchor an Erommy hardtop gazebo 14X22 to the ground on a compacted gravel base. The county approved them. Fairly easy to get into the ground with a compact wrench. We used 36 inch length as directed by our county. I submitted printed material from the website to obtain my permit. I live in a designated wetlands area on the east coast of Virginia where hurricanes are common. I do highly recommend this product. We agonized over how to position them and get them under the structure, but it wasn't as difficult as I thought it would be.
Was pleasantly surprised how easy it was to reverse the auger if I was off of the mark I wanted. And when it down 36" it's not going to move...very secure.
This was done by removing only one or two pavers. Drilling a 1" hole in the paver, and putting it over the Anchor shaft......
Super satisfied with the Foot Anchors
The important thing for me was being able to install the footings myself as a solo act. Your auger/plate system was perfect. Inclined grade was no issue. Dug 6-8” holes, installed 2x6” 23” square boxes, filled with pea gravel and installed augers. You can see the plates and post brackets. They look very cool.
These anchors made my deck project so easy! My Deck is so solid and I was able to knock it out in a few days rather than having to wait days for traditional concrete footings to set! If you’re on the fence about doing your deck with these, take my word, get them! I am thrilled. I’ve never built a deck before and I did a lot of research before doing it. I was so impressed with how quickly these anchors were to install. I was able to sink them and build my deck structure in less than half a day!
My wife and I installed 9 deck foot anchors on our 10x16 foot deck we built.The system worked great and was a small challenge for first-time install. This is a solid design using 6x6 post no digging holes no concrete. Very satisfied customer
I used these footing for a freestanding pool deck. They worked great and did exactly what i wanted them to do.
Great product easy to use as long as the soil conditions are conducive to this product. Would definitely use again
I've been using the deck foot anchor system for a few years now, and keep finding new applications for it.
Most recently I built a walkway through a small wooded area. As always - the deck foot made it a breeze!
I'm an ole dig 48" frost down type. But I had a unique situation, I had a fairly new slab and didn't want to destroy it. My engineer wanted helical anchors. Boom this is the perfect answer. So 15 cored holes later and 48" anchors I'm very pleased. This is a 10 x 34' free standing deck. Used 6x6 post with 2x10s, with cross bracing. Absolutely rigid no play whatsoever. Highly recommend. I used a Ryobi impact gun, more then ample to handle the install. I back filled the holes w cement, plus the flat plate perfect. Thank you so much. Customer svc, delivery, ordering all excellent.
Because of massive back orders Deckgo kept me well informed and , true to their word, the shipment arrived when predicted. The Pad with gravel is prepared but the Anchors and lumber are bedded down in the garage for the winter. I can’t wait to report back with pictures in a few months.
Used as deck anchors for 12x12 deck using 6x6 posts in very granular hillside soil in upstate New York. Observed large number of 2-6” thick shale rocks roughly 24” in diameter on surface and in ground while building short retaining wall slightly up hill from deck. Drove and removed 5/8” rebar 36” deep for each anchor to make sure the path was clear for the auger. Deck structured as space frame, so posts only need to float on the anchor pins. Should work well.
My only criticism of the post anchors is that the base plate design should allow for more eccentricity given that it is extremely difficult to drive an auger at precisely the location the design requires. The threaded pin on the auger almost certainly will not be centered where you want it and the post bracket allows for eccentricity in only one direction. It begs for hacks that may not be structurally sound.
So I started with 36” but ended up with 24”. Ground was too tuff and deWalt electric impact gun wouldn’t drive them much more than 27”. Was 1st time using them, maybe took same time as digging footings. Next time I would be quicker bc of this experience though.
© 2026, DecksGo Powered by Shopify